|
|
| Line 1: |
Line 1: |
| = Software Stack = | | = Resources for CS282 - Robotics = |
| === Ubuntu with Brad's Live ISO === | | ---- |
| # Make sure you have the latest version of the [http://cs.earlham.edu/~carrick/courses/cs282/cs282live_2.iso Live ISO] (as of this writing)
| | == Software Stack == |
| #* Recent improvements: Right and middle click from the mac touchpad, no longer need to use sudo when trying to access USB bus, based on latest Ubuntu version, new Bluetooth management tool
| | * [[nxt-python-iso|Ubuntu with Brad's Live ISO]] |
| # Boot off the live ISO, either on real hardware or virtually
| | * [[nxt-python-osx|OSX]] |
| # Login using cs282/johnny5
| |
| # Download [http://cs.earlham.edu/~carrick/courses/cs282/nxt.tgz Brad's installation kit] and untar it anywhere you want.
| |
| # In your editor of choice, modify the install.sh script to connect to your brick instead of Brad's. This will be within the first few lines.
| |
| # Open a terminal, navigate to the folder with your newly untarred files and type
| |
| sudo ./install.sh
| |
| If your computer supports bluetooth, set up your connection to your robot
| |
| # Turn on your brick.
| |
| # Navigate through the menu to enable bluetooth
| |
| #* Ensure that your device is set to "findable"
| |
| # Click the bluetooth symbol at the top of your computer's screen, next to the envelope.
| |
| # Select "Set up new device"
| |
| # Select your robot
| |
| # You will be prompted to input a passkey into your robot
| |
| #* Use the small grey button to delete characters and the large orange button to select characters
| |
| #* Select the checkmark to submit your passkey
| |
| #* Work quickly! You have about a minute before the passkey kicks you out and makes you start over!
| |
| #* You will be notified on-screen if your passkey was successful
| |
| # After your passkey is accepted, try running query.py
| |
|
| |
|
| === OSX === | | == Python == |
| * These instructions were tested under Snow Leopard (10.6.2), they will probably work under Leopard too.
| |
| * These instructions assume you already have Python, you can check this by typing <code>python</code> at a shell (aka Terminal) prompt. The Python interpreter should start, read the on-screen instructions to see how to exit it.
| |
| * Frequently it's easier to get USB working than it is Bluetooth, and they use much of the same underlying plumbing.
| |
| * You should test each step as you go, most of the packages have example code you can use to do this.
| |
| * Each of the steps below require that a package or files to be downloaded to your computer first. They are all available in the [http://cs.earlham.edu/~charliep/courses/cs282/packages CS282 packages] directory. Once you have downloaded the zip file you can un-zip it, cd to the created directory, and run the command listed below for that directory.
| |
| $ sudo python ez_setup.py -U setuptools # setuptools
| |
| $ sudo python setup.py install # py2app
| |
| $ sudo python setup.py install # lightblue
| |
| $ sudo python setup.py install # nxt-python-1.1
| |
| * Simon Levy's script (bluetooth.py*) must be in the directory that you are running the interpreter in for the Bluetooth interface to work. <i>Update: Release v1.1 appears to have integrated this script into the NXT-Python library.</i>
| |
| * For USB support you will need PyUSB, you can download it from its SourceForge [http://sourceforge.net/projects/pyusb site] and then install it.
| |
| * Once you think all the plumbing is working correctly you can use the query.py script in the [http://cs.earlham.edu/~charliep/courses/cs282/source CS282 source] directory to test it. <b>N.B.</b> Change the BlueTooth ID in query.py to match your NXT.
| |
| | |
| = Python = | |
| * [[nxt-python-doc|NXT-Python Documentation]] | | * [[nxt-python-doc|NXT-Python Documentation]] |
| * [[nxt-python-threads|Thread Notes]] | | * [[nxt-python-threads|Thread Notes]] |