Galileo: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
No edit summary |
||
| Line 2: | Line 2: | ||
This page specifically discusses the Galileo. Anything Arduino-specific should get relegated to [[Arduino|here]]. | This page specifically discusses the Galileo. Anything Arduino-specific should get relegated to [[Arduino|here]]. | ||
=info dump= | |||
IoTkit handles ethernet transactions. It connects to a host and sends a packet with [string, val] where val is the value you wish to send. | |||
There aren't any packages installed on their Linux distro. | |||
There's an interface for C++ that lets you access the Arduino. | |||
| Line 12: | Line 21: | ||
[[http://arduino.cc/en/ArduinoCertified/IntelGalileo Documentation on Arduino site]] | [[http://arduino.cc/en/ArduinoCertified/IntelGalileo Documentation on Arduino site]] | ||
[[https://communities.intel.com/docs/DOC-22226 Drivers]] | |||
[[https://communities.intel.com/docs/DOC-21882 BSP Build Guide]] | |||
[[https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=23171 Software Packages]] | |||
=Installation= | =Installation= | ||
# download the "getting started" document | |||
# download and extract "Intel Galileo Arduino SW 1.5.3" the Arduino IDE for Galileo | |||
# open Arduino and update the firmware via help -> firmware update | |||
# wait for completion | |||
# in device manager (or equivalent) find the device [specify] and install the drivers from "arduino-1.5.3/hardware/arduino/x86/tools" | |||
# note what COM port the Galileo is attached to | |||
# open Putty (or equivalent) and change the connection type to serial, speed to 115200, and the serial line to your specified COM port | |||
# save the settings and open the connection | |||
# wait for start up | |||
# log in as root; by default it has no password | |||
# download [[http://downloadmirror.intel.com/23171/eng/LINUX_IMAGE_FOR_SD_Intel_Galileo_v0.7.5.7z the linux image]] | |||
# extract the previous file to the micro SD card | |||
# close your putty | |||
# place the card into the Galileo and power cycle it | |||
# open putty again and reestablish the connection | |||
# it should work now; try running the "blink" sketch in arduino | |||
=Specs= | =Specs= | ||
Revision as of 22:48, 5 February 2014
The Galileo is a fusion of a Linux PC running Intel's architecture and an Arduino. The purpose is to provide the benefits of a pc (connectivity, power, storage, ports) with the benefits of an Arduino (an open-platform hardware interface.)
This page specifically discusses the Galileo. Anything Arduino-specific should get relegated to here.
info dump
IoTkit handles ethernet transactions. It connects to a host and sends a packet with [string, val] where val is the value you wish to send.
There aren't any packages installed on their Linux distro.
There's an interface for C++ that lets you access the Arduino.
Resources
[Documentation on Arduino site]
[Drivers]
Installation
- download the "getting started" document
- download and extract "Intel Galileo Arduino SW 1.5.3" the Arduino IDE for Galileo
- open Arduino and update the firmware via help -> firmware update
- wait for completion
- in device manager (or equivalent) find the device [specify] and install the drivers from "arduino-1.5.3/hardware/arduino/x86/tools"
- note what COM port the Galileo is attached to
- open Putty (or equivalent) and change the connection type to serial, speed to 115200, and the serial line to your specified COM port
- save the settings and open the connection
- wait for start up
- log in as root; by default it has no password
- download [the linux image]
- extract the previous file to the micro SD card
- close your putty
- place the card into the Galileo and power cycle it
- open putty again and reestablish the connection
- it should work now; try running the "blink" sketch in arduino