Difference between revisions of "Galileo"
Jump to navigation
Jump to search
(→Resources) |
(→Installation) |
||
| Line 37: | Line 37: | ||
* RS32 male -> usb male | * RS32 male -> usb male | ||
| − | # download | + | Documentation |
| + | [[https://communities.intel.com/servlet/JiveServlet/downloadBody/22204-102-1-25429/Galileo_GettingStarted_329685_005.pdf Getting Started 005]] | ||
| + | [[https://communities.intel.com/servlet/JiveServlet/downloadBody/21882-102-1-25153/Quark_BSPBuildGuide_329687_001.pdf BSP Build Guide 001]] | ||
| + | |||
| + | # download documentation | ||
# plug power into Galileo (always do this first) | # plug power into Galileo (always do this first) | ||
# join RS32 cables | # join RS32 cables | ||
# connect Galileo to the PC | # connect Galileo to the PC | ||
# download and extract "Intel Galileo Arduino SW 1.5.3" the Arduino IDE for Galileo | # download and extract "Intel Galileo Arduino SW 1.5.3" the Arduino IDE for Galileo | ||
| − | # open Arduino 1.5.3 | + | # open Arduino 1.5.3 |
| − | # wait | + | # change board to Galileo if necessary |
| + | # update the firmware via help -> firmware update | ||
| + | # wait, this might take a few minutes (the window will say when it's finished) | ||
# in device manager (or equivalent) find the device [specify] and install the drivers from "arduino-1.5.3/hardware/arduino/x86/tools" | # in device manager (or equivalent) find the device [specify] and install the drivers from "arduino-1.5.3/hardware/arduino/x86/tools" | ||
# note what COM port the Galileo is attached to | # note what COM port the Galileo is attached to | ||
| − | # open Putty (or equivalent) | + | # open Putty (or equivalent) |
| + | # change the connection type to serial, speed to 115200, and the serial line to your specified COM port | ||
# save the settings and open the connection | # save the settings and open the connection | ||
| − | # wait | + | # wait, this might take a few minutes (it's finished when a command [specify] is present and nothing is happening) |
# log in as root; by default it has no password | # log in as root; by default it has no password | ||
# download [[http://downloadmirror.intel.com/23171/eng/LINUX_IMAGE_FOR_SD_Intel_Galileo_v0.7.5.7z the linux image]] | # download [[http://downloadmirror.intel.com/23171/eng/LINUX_IMAGE_FOR_SD_Intel_Galileo_v0.7.5.7z the linux image]] | ||
| Line 55: | Line 62: | ||
# place the card into the Galileo and power cycle it | # place the card into the Galileo and power cycle it | ||
# open putty again and reestablish the connection | # open putty again and reestablish the connection | ||
| − | # it should work now; try running the "blink" sketch in | + | # it should work now; try running the "blink" sketch in Arduino |
| + | # the LED nearest the audio jack should light up | ||
=Specs= | =Specs= | ||
Revision as of 20:58, 5 February 2014
The Galileo is a fusion of a Linux PC running Intel's architecture and an Arduino. The purpose is to provide the benefits of a pc (connectivity, power, storage, ports) with the benefits of an Arduino (an open-platform hardware interface.)
This page specifically discusses the Galileo. Anything Arduino-specific should get relegated to here.
Contents
info dump
IoTkit handles ethernet transactions. It connects to a host and sends a packet with [string, val] where val is the value you wish to send.
There aren't any packages installed on their Linux distro.
There's an interface for C++ that lets you access the Arduino.
Resources
Downloads
[Drivers]
Installation
Materials
- Galileo board
- power adapter
- micro SD card
- micro usb male -> RS32 female
- RS32 male -> usb male
Documentation [Getting Started 005] [BSP Build Guide 001]
- download documentation
- plug power into Galileo (always do this first)
- join RS32 cables
- connect Galileo to the PC
- download and extract "Intel Galileo Arduino SW 1.5.3" the Arduino IDE for Galileo
- open Arduino 1.5.3
- change board to Galileo if necessary
- update the firmware via help -> firmware update
- wait, this might take a few minutes (the window will say when it's finished)
- in device manager (or equivalent) find the device [specify] and install the drivers from "arduino-1.5.3/hardware/arduino/x86/tools"
- note what COM port the Galileo is attached to
- open Putty (or equivalent)
- change the connection type to serial, speed to 115200, and the serial line to your specified COM port
- save the settings and open the connection
- wait, this might take a few minutes (it's finished when a command [specify] is present and nothing is happening)
- log in as root; by default it has no password
- download [the linux image]
- extract the previous file to the micro SD card
- close your putty
- place the card into the Galileo and power cycle it
- open putty again and reestablish the connection
- it should work now; try running the "blink" sketch in Arduino
- the LED nearest the audio jack should light up
