Difference between revisions of "Wattnode-lcd"

From Earlham CS Department
Jump to navigation Jump to search
(WattNode/WattsUp? Test Run)
Line 36: Line 36:
  
 
*Detail photos
 
*Detail photos
**[http://wiki.cs.earlham.edu/images/c/c5/Wattupjunction.JPG Junction Bar]
+
**http://wiki.cs.earlham.edu/images/c/c5/Wattupjunction.JPG  
**[http://wiki.cs.earlham.edu/images/2/2f/Wattsup.JPG WattsUp?]
+
Junction Bar
**[http://wiki.cs.earlham.edu/images/7/78/Wattnodetransf.JPG Transformer]
+
this was placed on the line side of the Wattnode setup. The line was cut and strung up with wires to the Watt node power section patched in. Our resident person less convinced of their invulnerability wrapped it up in tape.
**[http://wiki.cs.earlham.edu/images/d/dc/Wattnode.JPG WattNode]
+
**http://wiki.cs.earlham.edu/images/2/2f/Wattsup.JPG
**[http://wiki.cs.earlham.edu/images/2/2b/Egg.JPG Egg]
+
WattsUp basically fulfills the purpose of the Wattnode in a much prettier package. It lacks the ability to patch into a line without a plug such as a water heater, so our Wattnode will be used mainly in that affect
 +
**http://wiki.cs.earlham.edu/images/7/78/Wattnodetransf.JPG
 +
Transformer
 +
the transformer is a magnet loop that induces the amount of electricity passing through it. This induction is then measured by the wattnode. It's clipped onto the black, active line with the stickered face facing the source. The green line is the ground and the white line is the neutral.
 +
**http://wiki.cs.earlham.edu/images/d/dc/Wattnode.JPG  
 +
WattNode
 +
Because the test was conducted on a two-phase cable. The patch in from the junction bar was only the active and neutral cable. The unused third phase (the red/B section) was routed back onto itself with the short line of white cable on the left. The A section was then connected to the inducer and the output section was wired to the display.
 +
**http://wiki.cs.earlham.edu/images/2/2b/Egg.JPG Egg  
 +
strictly for morale purposes.

Revision as of 19:15, 3 July 2006

Preparing for the Test Run

  • Assembling Test Run Elements (June 28th)
    • Ingredients
      • Computer Power Cable
      • Soldering Iron
      • Junction Bar
      • WattNode Pro w/ 30 volt current transformer
      • Digital Display (preprogrammed for kwh)
      • Connection Rings
      • Spare wire
      • Pliers and Dikes and Roach Clips
      • Itty-bitty-teeny-weeny-green-flat-head screw driver
    • What Happened (on the day in question)
      • Recieved detailed insructions from Professor Peck (including emergency CPR procedures)
      • Learned to solder on connection rings and the process of tinning.
      • Cut open black insulation of power cable and attached current transformer (CT) around black wire facing the line side.
      • Chopped power cable in two on the line side of the CT and installed junction bar and spliced in black and white wires to power WattNode.
      • Connected digital display to WattNode (see pic below)
      • Connected CT to WattNode (using a tinned jumper wire to set up the WattNode for 120 VAC)
      • In a wild move of hyper-safety awareness our very own nervous nelly wrapped large amounts of electrical tape around junction bar.

The WattNode/WattsUp? Test Run

It was a dark and relatively quiet and cool evening on Dennis 4th floor. Colin and Ehren started by plugging the WattsUp? device into the powerstrip and plugging the hacked power cable into the WattsUp? and the computer. By organizing the equipment in series, these two strapping lads were able to see if both devices returned the same result.

http://wiki.cs.earlham.edu/images/a/af/Wattupbefore.JPG

from a mess of wires

http://wiki.cs.earlham.edu/images/9/9c/Wattupafter.JPG

to beauty and perfection

As a service to anyone trying to understand what the heck the setup looked like this picture was carefully taken:

http://wiki.cs.earlham.edu/images/7/79/Wattupsetup.JPG

Junction Bar this was placed on the line side of the Wattnode setup. The line was cut and strung up with wires to the Watt node power section patched in. Our resident person less convinced of their invulnerability wrapped it up in tape.

WattsUp basically fulfills the purpose of the Wattnode in a much prettier package. It lacks the ability to patch into a line without a plug such as a water heater, so our Wattnode will be used mainly in that affect

Transformer the transformer is a magnet loop that induces the amount of electricity passing through it. This induction is then measured by the wattnode. It's clipped onto the black, active line with the stickered face facing the source. The green line is the ground and the white line is the neutral.

WattNode Because the test was conducted on a two-phase cable. The patch in from the junction bar was only the active and neutral cable. The unused third phase (the red/B section) was routed back onto itself with the short line of white cable on the left. The A section was then connected to the inducer and the output section was wired to the display.

strictly for morale purposes.