Difference between revisions of "Galileo"
Jump to navigation
Jump to search
(→Installation) |
(→Installation) |
||
| Line 37: | Line 37: | ||
* RS32 male -> usb male | * RS32 male -> usb male | ||
| − | |||
| − | + | Downloads | |
| − | + | # [[https://communities.intel.com/servlet/JiveServlet/downloadBody/22204-102-1-25429/Galileo_GettingStarted_329685_005.pdf Getting Started 005]] | |
| − | + | # [[https://communities.intel.com/servlet/JiveServlet/downloadBody/21882-102-1-25153/Quark_BSPBuildGuide_329687_001.pdf BSP Build Guide 001]] | |
| − | + | # go [[https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=23171 here]] and download "Intel Galileo Arduino SW 1.5.3" and "LINUX IMAGE FOR SD for Intel Galileo" | |
| − | |||
| − | |||
| − | # download | ||
Cables | Cables | ||
| Line 53: | Line 49: | ||
Arduino | Arduino | ||
| − | # | + | # extract "Intel Galileo Arduino SW 1.5.3" |
| − | # open Arduino 1.5.3 | + | # open the executable for Arduino 1.5.3 |
# change board to Galileo if necessary | # change board to Galileo if necessary | ||
# update the firmware via help -> firmware update | # update the firmware via help -> firmware update | ||
| Line 61: | Line 57: | ||
Drivers | Drivers | ||
# in device manager (or equivalent) find the device [specify] and install the drivers from "arduino-1.5.3/hardware/arduino/x86/tools" | # in device manager (or equivalent) find the device [specify] and install the drivers from "arduino-1.5.3/hardware/arduino/x86/tools" | ||
| − | # the | + | # note the COM port of the device [specify] |
Serial Connection | Serial Connection | ||
| + | # get [[http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html Putty]] (or equivalent) | ||
# open Putty (or equivalent) | # open Putty (or equivalent) | ||
# change the connection type to serial, speed to 115200, and the serial line to your specified COM port | # change the connection type to serial, speed to 115200, and the serial line to your specified COM port | ||
| − | # save the settings and open | + | # save the settings and click the open button |
# wait, this might take a few minutes (it's finished when the command [specify] is present and nothing is happening) | # wait, this might take a few minutes (it's finished when the command [specify] is present and nothing is happening) | ||
# log in as root; by default it has no password | # log in as root; by default it has no password | ||
| − | # | + | # extract[[http://downloadmirror.intel.com/23171/eng/LINUX_IMAGE_FOR_SD_Intel_Galileo_v0.7.5.7z the linux image]] to the micro SD card |
| − | |||
# close your putty | # close your putty | ||
| − | # | + | # put the micro SD card into the Galileo |
| + | # remove both cables from the Galileo and wait a few seconds | ||
| + | # replace the power cable then the usb cable | ||
# open putty again and reestablish the connection | # open putty again and reestablish the connection | ||
Revision as of 22:12, 5 February 2014
The Galileo is a fusion of a Linux PC running Intel's architecture and an Arduino. The purpose is to provide the benefits of a pc (connectivity, power, storage, ports) with the benefits of an Arduino (an open-platform hardware interface.)
This page specifically discusses the Galileo. Anything Arduino-specific should get relegated to here.
Contents
info dump
IoTkit handles ethernet transactions. It connects to a host and sends a packet with [string, val] where val is the value you wish to send.
There aren't any packages installed on their Linux distro.
There's an interface for C++ that lets you access the Arduino.
Resources
Downloads
[Drivers]
Installation
Materials
- Galileo board
- power adapter
- micro SD card
- micro usb male -> RS32 female
- RS32 male -> usb male
Downloads
- [Getting Started 005]
- [BSP Build Guide 001]
- go [here] and download "Intel Galileo Arduino SW 1.5.3" and "LINUX IMAGE FOR SD for Intel Galileo"
Cables
- plug power into Galileo (always do this first)
- join RS32 cables
- connect Galileo to the PC
Arduino
- extract "Intel Galileo Arduino SW 1.5.3"
- open the executable for Arduino 1.5.3
- change board to Galileo if necessary
- update the firmware via help -> firmware update
- wait, this might take a few minutes (the window will say when it's finished)
Drivers
- in device manager (or equivalent) find the device [specify] and install the drivers from "arduino-1.5.3/hardware/arduino/x86/tools"
- note the COM port of the device [specify]
Serial Connection
- get [Putty] (or equivalent)
- open Putty (or equivalent)
- change the connection type to serial, speed to 115200, and the serial line to your specified COM port
- save the settings and click the open button
- wait, this might take a few minutes (it's finished when the command [specify] is present and nothing is happening)
- log in as root; by default it has no password
- extract[the linux image] to the micro SD card
- close your putty
- put the micro SD card into the Galileo
- remove both cables from the Galileo and wait a few seconds
- replace the power cable then the usb cable
- open putty again and reestablish the connection
Testing Arduino
- it should work now; try running the "blink" sketch in Arduino
- the LED nearest the audio jack should light up
