HIP:PMP:Minicom - Revision history

Madunnh at 16:42, 10 July 2006

2006-07-10T16:42:31Z

← Older revision		Revision as of 16:42, 10 July 2006
Line 35:		Line 35:
	CTRL-A Z for help \| 115200 8N1 \| NOR \| Minicom 2.00.0 \| VT102 \| Online		CTRL-A Z for help \| 115200 8N1 \| NOR \| Minicom 2.00.0 \| VT102 \| Online
	* minicom will also display the PMP's output, which will looke like this...		* minicom will also display the PMP's output, which will looke like this...
			SYSLINUX 2.11 2004-08-16 Copyright (C) 1994-2004 H. Peter Anvin

			"linux" to run Linux with /dev/hda2 as root (default after 5 sec.)
			"nfs" to run Linux with NFS exported directory on host as root
			"initrd".to run Linux with an initial RAM disk image as root
			"dos" to run DOS-ROM (Linux can be run using loadlin.exe)
			Serial
			boot:
			Loading bzimage................Ready.
			Linux version 2.4.23-2.5-ts (root@codd.cs.earlham.edu) (gcc version 3.3.2 20031022 (Red Hat Linux 3.3.2-1)) #1 Tue Jun 13 6
			BIOS-provided physical RAM map:
			BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)
			BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
			BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
			BIOS-e820: 0000000000100000 - 0000000002000000 (usable)
			BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
			32MB LOWMEM available.
			On node 0 totalpages: 8192
			....

Madunnh at 16:34, 10 July 2006

2006-07-10T16:34:25Z

← Older revision		Revision as of 16:34, 10 July 2006
Line 29:		Line 29:
	*Jumper 4 makes output to be readable with minicom		*Jumper 4 makes output to be readable with minicom
	Run minicom		Run minicom
	~$ sudo minicom		~$ sudo minicom
	Boot PMP		Boot PMP
	* minicom should change from offline to online, if the connection is established		* minicom should change from offline to online, if the connection is established

Madunnh at 16:33, 10 July 2006

2006-07-10T16:33:39Z

← Older revision		Revision as of 16:33, 10 July 2006
Line 23:		Line 23:

	=== PMP Settings for Output with minicom ===		=== PMP Settings for Output with minicom ===
	1. Turn off PMP		# Turn off PMP
	2. Connect COM2 of PMP to COM1 of linux machine where minicom is installed		# Connect COM2 of PMP to COM1 of linux machine where minicom is installed
	3. Put on jumpers 2 and 4 on the PMP		# Put on jumpers 2 and 4 on the PMP
	* Jumper 2 enables output to COM2 of PMP		*Jumper 2 enables output to COM2 of PMP
	* Jumper 4 makes output to be readable with minicom		*Jumper 4 makes output to be readable with minicom
	4. Run minicom		Run minicom
	~$ sudo minicom		~$ sudo minicom
	5. Boot PMP		Boot PMP
	* minicom should change from offline to online, if the connection is established		* minicom should change from offline to online, if the connection is established
	CTRL-A Z for help \| 115200 8N1 \| NOR \| Minicom 2.00.0 \| VT102 \| Offline		CTRL-A Z for help \| 115200 8N1 \| NOR \| Minicom 2.00.0 \| VT102 \| Offline
	CTRL-A Z for help \| 115200 8N1 \| NOR \| Minicom 2.00.0 \| VT102 \| Online		CTRL-A Z for help \| 115200 8N1 \| NOR \| Minicom 2.00.0 \| VT102 \| Online
	* minicom will also display the PMP's output, which will looke like this...		* minicom will also display the PMP's output, which will looke like this...

Madunnh at 16:32, 10 July 2006

2006-07-10T16:32:06Z

Madunnh at 16:30, 10 July 2006

2006-07-10T16:30:53Z

← Older revision		Revision as of 16:30, 10 July 2006
Line 1:		Line 1:
	=== Installing minicom ===		===Installing minicom===
	Alex / Colin will fill this one...		Alex / Colin will fill this one...

	=== Configuring Minicom for PMP ===		===Configuring Minicom for PMP===
	~$ sudo minicom		~$ sudo minicom
	If minicom was correctly installed, you shoud see something like this...		If minicom was correctly installed, you shoud see something like this...

Madunnh at 16:29, 10 July 2006

2006-07-10T16:29:51Z

← Older revision		Revision as of 16:29, 10 July 2006
Line 23:		Line 23:

	=== PMP Settings for Output with minicom ===		=== PMP Settings for Output with minicom ===
	# Turn off PMP		1. Turn off PMP
	# Connect COM2 of PMP to COM1 of linux machine where minicom is installed		2. Connect COM2 of PMP to COM1 of linux machine where minicom is installed
	# Put on jumpers 2 and 4 on the PMP		3. Put on jumpers 2 and 4 on the PMP
	* Jumper 2 enables output to COM2 of PMP		* Jumper 2 enables output to COM2 of PMP
	* Jumper 4 makes output to be readable with minicom		* Jumper 4 makes output to be readable with minicom
	# Run minicom		4. Run minicom
	~$ sudo minicom		~$ sudo minicom
	# Boot PMP		5. Boot PMP
	* minicom should change from offline to online, if the connection is established		* minicom should change from offline to online, if the connection is established
	CTRL-A Z for help \| 115200 8N1 \| NOR \| Minicom 2.00.0 \| VT102 \| Offline		CTRL-A Z for help \| 115200 8N1 \| NOR \| Minicom 2.00.0 \| VT102 \| Offline
	CTRL-A Z for help \| 115200 8N1 \| NOR \| Minicom 2.00.0 \| VT102 \| Online		CTRL-A Z for help \| 115200 8N1 \| NOR \| Minicom 2.00.0 \| VT102 \| Online
	* minicom will also display the PMP's output, which will looke like this...		* minicom will also display the PMP's output, which will looke like this...

Madunnh at 16:28, 10 July 2006

2006-07-10T16:28:05Z

← Older revision		Revision as of 16:28, 10 July 2006
Line 26:		Line 26:
	# Connect COM2 of PMP to COM1 of linux machine where minicom is installed		# Connect COM2 of PMP to COM1 of linux machine where minicom is installed
	# Put on jumpers 2 and 4 on the PMP		# Put on jumpers 2 and 4 on the PMP
	* Jumper 2 enables output to COM2 of PMP		* Jumper 2 enables output to COM2 of PMP
	* Jumper 4 makes output to be readable with minicom		* Jumper 4 makes output to be readable with minicom
	# Run minicom		# Run minicom
	~$ sudo minicom		~$ sudo minicom
	# Boot PMP		# Boot PMP
	* minicom should change from offline to online, if the connection is established		* minicom should change from offline to online, if the connection is established
	CTRL-A Z for help \| 115200 8N1 \| NOR \| Minicom 2.00.0 \| VT102 \| Offline		CTRL-A Z for help \| 115200 8N1 \| NOR \| Minicom 2.00.0 \| VT102 \| Offline
	CTRL-A Z for help \| 115200 8N1 \| NOR \| Minicom 2.00.0 \| VT102 \| Online		CTRL-A Z for help \| 115200 8N1 \| NOR \| Minicom 2.00.0 \| VT102 \| Online
	* minicom will also display the PMP's output, which will looke like this...		* minicom will also display the PMP's output, which will looke like this...

Madunnh at 16:27, 10 July 2006

2006-07-10T16:27:25Z

← Older revision		Revision as of 16:27, 10 July 2006
Line 24:		Line 24:
	=== PMP Settings for Output with minicom ===		=== PMP Settings for Output with minicom ===
	# Turn off PMP		# Turn off PMP
			# Connect COM2 of PMP to COM1 of linux machine where minicom is installed
			# Put on jumpers 2 and 4 on the PMP
			* Jumper 2 enables output to COM2 of PMP
			* Jumper 4 makes output to be readable with minicom
			# Run minicom
			~$ sudo minicom
			# Boot PMP
			* minicom should change from offline to online, if the connection is established
			CTRL-A Z for help \| 115200 8N1 \| NOR \| Minicom 2.00.0 \| VT102 \| Offline
			CTRL-A Z for help \| 115200 8N1 \| NOR \| Minicom 2.00.0 \| VT102 \| Online
			* minicom will also display the PMP's output, which will looke like this...

Madunnh at 16:15, 10 July 2006

2006-07-10T16:15:56Z

← Older revision		Revision as of 16:15, 10 July 2006
Line 15:		Line 15:
	* Press CTRL-A Z to see minicom menu		* Press CTRL-A Z to see minicom menu

			# Press CTRL-A O for 'configurations'
			# Select 'serial port setup' on the menu
			# Set A 'serial device' to /dev/ttyS0
			# Set E 'Bps/Par/Bits' to 115200 8N1
			# Press Esc and 'save setup as dfl'
			# Exit minicom

	=== PMP Settings for Output with minicom ===		=== PMP Settings for Output with minicom ===
			# Turn off PMP

Madunnh at 16:04, 10 July 2006

2006-07-10T16:04:43Z

@@ Line 1: / Line 1: @@
 === Installing minicom ===
 === Configuring Minicom for PMP ===
 === PMP Settings for Output with minicom ===

← Older revision		Revision as of 16:32, 10 July 2006
Line 23:		Line 23:

	=== PMP Settings for Output with minicom ===		=== PMP Settings for Output with minicom ===
	1. Turn off PMP		1. Turn off PMP
	2. Connect COM2 of PMP to COM1 of linux machine where minicom is installed		2. Connect COM2 of PMP to COM1 of linux machine where minicom is installed
	3. Put on jumpers 2 and 4 on the PMP		3. Put on jumpers 2 and 4 on the PMP
	* Jumper 2 enables output to COM2 of PMP		* Jumper 2 enables output to COM2 of PMP
	* Jumper 4 makes output to be readable with minicom		* Jumper 4 makes output to be readable with minicom
	4. Run minicom		4. Run minicom
	~$ sudo minicom		~$ sudo minicom
	5. Boot PMP		5. Boot PMP
	* minicom should change from offline to online, if the connection is established		* minicom should change from offline to online, if the connection is established
	CTRL-A Z for help \| 115200 8N1 \| NOR \| Minicom 2.00.0 \| VT102 \| Offline		CTRL-A Z for help \| 115200 8N1 \| NOR \| Minicom 2.00.0 \| VT102 \| Offline
	CTRL-A Z for help \| 115200 8N1 \| NOR \| Minicom 2.00.0 \| VT102 \| Online		CTRL-A Z for help \| 115200 8N1 \| NOR \| Minicom 2.00.0 \| VT102 \| Online
	* minicom will also display the PMP's output, which will looke like this...		* minicom will also display the PMP's output, which will looke like this...